GETTING FAMILIAR WITH PLUMBING: YOUR STARTING POINT FOR WHEN INSTALLING A BATHTUB

Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub

Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub

Blog Article

Free Quote

Right here below you can discover lots of helpful resources around Tools You Need to Install a New Bathtub .


How to Install a Bathtub Yourself
Installing a bathtub isn't specifically brain surgery, but it does require strong plumbing, woodworking, and also sometimes, tiling abilities. Replacing an old tub with a brand-new one is likewise a moderately tough job. If the old bathtub is conveniently obtainable, the project can relocate quickly; if you have to open a wall to get rid of the old bathtub as well as place the new bathtub, the task is a lot harder. In either instance, the task is within a home handyman's abilities, although you will require a helper to vacate the old bathtub as well as set in the brand-new one. Make certain you have qualified on your own for the work and also are comfortable attempting it. Rather than working with a professional to take control of a halfway-completed job, it is better to consider utilizing one prior to you start. Opportunities are you may need a specialist plumber to make tube connections.
This write-up will certainly assist you install a brand-new bathtub in your restroom if you have actually currently purchased a new bathtub and do not need to transform the plan of your previous supply of water pipes.
Your devices as well as product checklist must consist of the following:
  • New Bathtub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipeline Caps


  • Planning for the Installation


    To start with, the supporting structure supplied with the bathroom must be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to see to it that if the tap comes with a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets device to prevent pressure on the tub.
    Fit the versatile faucet adapters to the bottom of the two taps using 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you use every one of the provided washers.
    Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath should currently be ready to be fitted in its final placement.

    Removing Old Taps


    If you need to change old taps with new ones as a part of your installment, then the first thing you must do is detach the water system. After doing so, switch on the taps to drain pipes any type of water continuing to be in the system. The procedure of removing the existing taps can be quite troublesome as a result of the limited gain access to that is typically the instance.
    Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the faucets. Have a towel all set for the remaining water that will originate from the pipes. Once the supply pipelines have been removed, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning throughout this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any kind of old securing substance.
    Before carrying on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the new taps to fit.

    Mounting the Tub


    Utilizing both wood boards under its feet, put the bathtub in the needed position. The wood boards are handy in evenly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto four little factors.
    The next goal is to guarantee that the tub is leveled all round. This can be accomplished by checking the level as well as readjusting the feet on the tub till the spirit level reviews degree.
    To install faucets, fit the bottom of the outermost flexible faucet connector to the appropriate supply pipe by making a compression sign up with; then do the exact same for the various other tap.
    Activate the water supply as well as examine all joints and new pipework for leakages and tighten them if required. Fill up the tub as well as also examine the overflow electrical outlet as well as the typical outlet for leakages.
    Ultimately, take care of the bath paneling as defined in the maker's user's manual. Tiling as well as sealing around the bath tub needs to wait till the bathtub has actually been utilized at least when as this will certainly settle it into its last setting.

    Fitting New Taps


    If the tails of the new faucets are plastic, then you will require a plastic connector to prevent damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end offers a connection to the current supply pipes.
    If you require to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
    Next off, position the tap in the mounting opening in the bath/basin guaranteeing that the washers are in area between the tap and the sink. Secure the tap in position with the supplier supplied backnut. Once the faucet is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular faucet connectors. The previous kind ought to be attached to the tap ends initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.

    Tiling Around the Tub


    In the location where the bathroom satisfies the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to break a stiff seal, creating the water to penetrate the wall surface in between the bathroom and the tiling, resulting in complications with wetness and feasible leakages to the ceiling below.
    You can pick from a range of coloured sealers to assimilate your components and fittings. They are offered in tubes and also cartridges, and also are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of drenched paper or soft rope. Remember to always fill up the bathtub with water before sealing, to permit the movement experienced when the bathtub is in usage. The sealer can fracture fairly early if you do not take into account this motion prior to sealing.
    Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise easily available on the market. It is advisable to fit the floor tiles utilizing water-resistant or waterproof sticky and also grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    We hope you liked our piece on Installing A Bathtub. Many thanks for taking time to browse our piece. In case you enjoyed reading our page please make sure you remember to pass it around. Thank you for your time invested reading it.


    Top service? Contact.

    Report this page